Sign In
New User? Sign Up

Engineering

Questions in Engineering

Sort by:

What is TTT and CCT in metalurgy? Show me the diagrams for these two.?
- 0 Stars
- In Engineering -
- Asked by giant -
- 1 answer -
- 4 hours ago
each layer of the ozone's surface area measurement and volume?
- 0 Stars
- In Engineering -
- Asked by SOLO -
- 0 answers -
- 9 hours ago
in pump motor capacity calculation only Flow rate, Discharge Head, fluid density & efficiency are considered?
- 0 Stars
- In Engineering -
- Asked by POTATO -
- 2 answers -
- 12 hours ago
With a computer-based CAT test, how should I do rough work/calculations?
- 0 Stars
- In Engineering -
- Asked by Rohan N -
- 1 answer -
- 15 hours ago
Safety Evaluation of Servo Motors:?
- 0 Stars
- In Engineering -
- Asked by Vivek -
- 0 answers -
- 15 hours ago
Why are blades of a windmill turbine twisted?
- 0 Stars
- In Engineering -
- Asked by akash -
- 1 answer -
- 15 hours ago
can any one say where i findprevious qution papers of vishweshwaraiah technological university(vtu)?
- 0 Stars
- In Engineering -
- Asked by sonu -
- 0 answers -
- 16 hours ago
To search a job in Singapore as maintenance engineer with instrumentation back ground B.E.EEE 8 yrs experience?
- 0 Stars
- In Engineering -
- Asked by balasubramani -
- 1 answer -
- 16 hours ago
when motors provided with autoreset protectors are rated at ambients like -20 C, can we test at + 20 C~+40 Deg?
- 1 Stars
- In Engineering -
- Asked by Vivek -
- 0 answers -
- 16 hours ago
if a heater gives 100deg delta T and heats 100m3 oil how much heat duty required.?
- 0 Stars
- In Engineering -
- Asked by Shetty S -
- 1 answer -
- 17 hours ago
what are the advantages and disadvatages of surface, conduit and trunkng systems of wiring?
- 0 Stars
- In Engineering -
- Asked by saa -
- 2 answers -
- 17 hours ago
why martensite formation is easier in alloy steel than plain carbon steel?
- 0 Stars
- In Engineering -
- Asked by wtite pearl -
- 1 answer -
- 17 hours ago
What is the effect of distribution pressure on per capita water demand ?
- 0 Stars
- In Engineering -
- Asked by Balbir Kumar -
- 2 answers -
- 21 hours ago
Why are water intakes generally placed on upstream of sewage outfall ?
- 0 Stars
- In Engineering -
- Asked by Balbir Kumar -
- 1 answer -
- 21 hours ago
What is the purpose of providing a nozzle at the end of pipes ?
- 0 Stars
- In Engineering -
- Asked by Balbir Kumar -
- 3 answers -
- 21 hours ago
What are the two advantages associated with intermittent method of water supply ?
- 0 Stars
- In Engineering -
- Asked by Balbir Kumar -
- 1 answer -
- 21 hours ago
What is the system of studying Biomedical Engg course in India. What are the procedures and good colleges.?
- 0 Stars
- In Engineering -
- Asked by vijay a -
- 1 answer -
- 22 hours ago
I want to start trading unit of all types of flat & bend toughned safety glass?
- 0 Stars
- In Engineering -
- Asked by Rakesh Patel -
- 1 answer -
- 1 day ago
how to attest aieee form?
- 0 Stars
- In Engineering -
- Asked by Anup -
- 3 answers -
- 1 day ago
whether the armour of the cable to earthed by both sides or at one side only?
- 0 Stars
- In Engineering -
- Asked by sri -
- 4 answers -
- 1 day ago

Go to Page

79 results

Answers International

Yahoo! does not evaluate or guarantee the accuracy of any Yahoo! Answers content. Click here for the Full Disclaimer.

Help us improve Yahoo! Answers. Tell us what you think.

Copyright © 2009 Yahoo! Inc. All Rights Reserved.