Furnace burners go out?

My house was built in 1988 and has the original heating and air system, the furnace is made by Day n Night. Everything was still working fine until yesterday.  When I turn the heater on the pilot light goes on then after a minute all the burners light just fine and the blower fan runs. Well after a couple of minutes all the burners go out but the pilot light stays lit and the fan keeps running.  Once all the burners go out the pilot will stay lit making the ignition ticking sound but the burners will not ignite anymore.  If I turn the thermostat off and back on it will do the same thing all over again.  I did replace the filter and installed a new thermostat but im still having the same problem.  Any advice would be appreciated.  Thanks 

5 Answers

  • Anonymous
    3 weeks ago

    In 1923 priests tried to change the calendar; Holy Fire didn't come down; Turkish guards killed these priests; Ruski Orthodox replaced them.

    Holy Fire ended with Patriarch Irenaios. Now it's faked by heretics. Irenaios is the last Orthodox Patriarch. Irenaios blessed Catacomb movement.

    What you need is antimins (remains of saints sewed into a towel, one cup, one spoon, wax candles, nonkosher non-yeast nonbarcoded nonqrcoded bread/wine, etc.)

    Electricity is from Satan; yeast is grown on pig bacteria, etc.

    Barcode = Druid black magic curse; QRcode = ancient Mayan curse...

    Kosher (K) or Union of Orthodox Synagogues (U) = sprinkled with blood like Mosis did. Underneath the entrance of synagogue lies New Testament...

    Orthodoxy = the only true faith; Roman Catholics tried one cup - one spoon ritual and got sick with Bubonic plague; if heresy enters Orthodox monastery then monks/nuns will get sick with flu/tuberculosis (for instance); Orthodox churches who closed for COVID or had disposable cups/spoons or dipped spoon into alcohol are no longer brides of Christ (now they serve Satan and honor Satan's new COVID religion).

    Don’t go into UFO to be “healed” by evil demons; demons never do good.

    SSN is written as a barcode/QRcode; then it's put into a chip; chip is put into vaccine; chipped people are influenced (by super computers) to receive grey plastic card World Passport with no name on it (but when they stretch their hands to get it, gov't clerk presses secret button to administer the unforgivable green 666 tattoo by isotope rays). If you reject mark of the beast then your direct ancestors go to heaven (according to saint Vyacheslav Krasheninnikov from Ural).

    Birds participate in time creation. It's a sin to kill birds. Dinosaurs live under our level; they will get out through sinkholes and lakes; to kill them, go for their nerves. Save the birds; but kill the dinosaurs. First dinosaur will come out of Volga River in Russia. Scientists don't see dinosaurs under our level because of radiation. Sinkholes happen because people dig for resources underground and because earth is heating up.

    Source(s): mRNA vaccine by Moderna contains *Luciferin* dissolved with *66.6* ml of distilled *phosphate* buffer solution... ...mark of the beast...that's what it is... all vaccines are chipped; all vaccines have cells of aborted fetuses in them; Hank Aaron died from the COVID-19 vaccine
  • 1 month ago

    As a general rule of thumb, if you're  not qualified to work on a gas appliance, you should simply call someone who is. 

    That said, it may be a simple fix for a sensor in one place or another. I recently worked on one having similar problems and we traced it to a defective cable connector attached to a control board.  It's not always as easy as some of the other answers here seem to imply, and messing it up could be dangerous in many ways.

  • 1 month ago

    I think it's because of a bad flame sensor. You should call your nearby HVAC professional as soon as possible and repair your furnace. 

  • Anonymous
    1 month ago

    Could be a bad or dirty flame sensor.  Call a heating technician.

  • What do you think of the answers? You can sign in to give your opinion on the answer.
  • 1 month ago

    Oh good heavens! There is a temperature probe that senses when your pilot light is on. And without that temperature probe working properly the burners will keep shutting themselves off. Follow the pilot light and find the temperature probe that sticks right in to the pilot light that's what needs replacing. Replace that thing and everything will work correctly again

Still have questions? Get answers by asking now.